The numerical simulation of sheet forming can predict and display crinkling, drawing breakage and variation of sheet thickness in the process of drawing. The physical process, mechanical model and typical simulation process for sheet forming are described.

To the question of wrinkle and drawing breakage during the rectangle box forming process, this paper describes the simulation of rectangle box deep drawing by Marc finite element analysis software.

针对矩形盒成形过程中各种形式的起皱和拉裂问题，采用MSC.Marc有限元分析软件对矩形盒深拉延成形过程进行模拟。

互联网摘选

It can be concluded that the crack of skin is the macroscopic breakage form of grape and the maximal tensile stress is the main factor causing the mechanical damage of grape through comparing the model calculation with the experimental results.

经模型计算与试验结果相比较，得出表皮破裂是葡萄宏观破坏的主要形式，最大拉应力是造成葡萄机械损伤的主要原因。

互联网摘选

Objective Observes the toxic response that the animal complete skin and the breakage skin contact disinfection drugs internal short-term.

目的观察动物完整皮肤及破损皮肤短期内接触消毒药品所产生的毒性反应。

互联网摘选

Methods Carries on the artificial skin breakage toxicity experiment using 2% glutaraldehyde, 0.2% and 2% peracetic acid and 0.2% sodium hypochlorite were applied to skin shaving wound in guinea pigs, and toxic changes and death of the animals were observed.

方法利用2%戊二醛、0.2%过氧乙酸、2%过氧乙酸、0.2%次氯酸钠对豚鼠进行人为皮肤破损毒性实验，观察豚鼠全身中毒表现和死亡情况。

互联网摘选

Results The pathogenic invasive pathways included: 19 cases of urinary tract, 17 cases of respiratory tract, 7 cases of intravenous catheter detain, 7 cases of biliary tract, 1 case of skin breakage, and 7 cases of unclear origin.

结果58例败血症患者致病菌入侵途径分别为：泌尿系统19例，呼吸系统17例，深静脉导管7例，胆管7例，破损皮肤1例，入侵途径未明7例。

互联网摘选

Observation on therapeutic effect of patients with skin breakage and bedsore treated by biofluid gauze dressing change

生物流体敷料膜换药治疗皮肤破损及压疮的疗效观察

互联网摘选

Those troubles can not only greatly affect the improvement of productivity of the ZR mill, but also severely damage the rolling equipments, so how to solve the problems of strip breakage and roll wind-up has long been an important subject of our research work.

这不仅会严重影响轧机生产率的提高，而且还会损坏设备。因此，长期以来，如何解决断带与缠辊的问题已成为重要的研究课题。

互联网摘选

Large quantity of rejected products involving edge crack and strip breakage are prone to occur in hot and cold rolling of the oriented silicon steel sheets due to high brittleness of the steel caused by its high silicon content.

取向硅钢含硅量高，钢质脆性大，在热轧和冷轧过程中容易产生大量边裂及断带轧废。

互联网摘选

Strip breakage and roll wind-up frequently occur on the ZR 20 when rolling the fragile stock with severe quality problems such as worse shape, serious surface and edge defects.

森吉米尔轧机（ZR20）在轧制板形不好、板面和边部有严重缺陷的脆性原料时，经常出现的生产故障是断带缠辊。

互联网摘选

Strip breakage happened very often in the annealing assembly line at the silicon steel workshop of Wuhan Iron& Steel Corp.

武钢硅钢厂退火生产线经常发生因带钢跑偏造成断带事故。

互联网摘选

Study on Strip Breakage Inside Furnace of Continuous Annealing Line of Cold Rolled Sheet

冷轧薄板连续退火线炉内断带原因分析

互联网摘选

Measurement and analysis on strip breakage and roll wind-up on ZR mill

ZR轧机断带缠辊的测试及研究

互联网摘选

However, when the content of Si is about 10%, its plasticity is poor, particularly in cold-rolling process. The poor plasticity led to the strip breakage in rolling process and it reduced the rate of finished products.

然而，4004Al-Si合金，由于含Si量在10%左右，塑性差，特别是冷轧性能差，进而导致轧制过程中易产生断带，成品率低。

互联网摘选

The cause for roll collar breakage and countermeasures as well as the effect after implementing at Bar and Wire Rood Plant were analyzed.

分析我厂造成高速线材轧机辊环碎辊的原因，提出改进措施以及实施后的效果。

互联网摘选

Causes to roll breakage of two high rolling mill in plate mill and preventative measures

轧板厂二辊轧机断辊原因及防范措施

互联网摘选

An Analysis of Work Roll Breakage of Tandem Mill

武钢冷轧厂五机架工作辊断裂原因分析及改进措施

互联网摘选

Resolution the steel rolling problem of roll breakage with heat ageing method

用热时效法解决轧钢的断辊问题

互联网摘选

The roll breakage status and its causes in the First Bar Production Line in last two years have been introduced, and the countermeasures for reducing the roll breakage have been put forward.

分析了棒线厂一棒生产线近两年来发生的断辊情况及原因，并提出了减少断辊所采取的有效措施。

互联网摘选

On-line Monitoring of Cutting Tool Breakage in Milling Operation Based on Cutting Force

基于切削力的铣刀破损实时监测技术研究

互联网摘选

Study on The In-process Monitoring and System for Tool Breakage

刀具破损在线监测及其系统的研究

互联网摘选