1、

In many cases of stainless steel cutting operations with carbide tools, a tool life strongly depends on flank notch wear of depth of cut rather than average flank wear of main cutting edge.

硬质合金刀具在不锈钢加工中,其刀具耐用度主要是取决于后刀面边界磨损而不是主切削刃后刀面的平均磨损量。

互联网摘选

2、
3、

There is a cyclonic circulation in the northern part of the SCS, and its strength and scope decrease with the depth increases.

在南海北部存在一个气旋性环流,这个环流的强度和范围随深度增加而减小。

互联网摘选

4、

However, compared with traditional cylindrical spool valve, most anomalous orifices still face some problems, for instance, existing research data or achievements are less, study on characteristics lack depth or are incomplete.

然而,与传统圆柱形滑阀相比,多数异形阀口滑阀还存在着已有研究资料、成果少,以及特性研究不深入、不完善等问题。

互联网摘选

5、

The wearing depth distribution of different contact positions of typical kinematic pair is discussed.

研讨了典型运动副不同接触位置的磨损深度分布情况。

互联网摘选

6、

Basing on Archard wear model, the rule of die wear is studied by simulation, and the relation between wearing depth and the times of die service is found by means of unitary linearly regression, then the service life of die is previewed.

基于Archard磨损模型,对直齿轮温挤压模具的磨损规律进行分析,并利用一元线性回归法,找出模具表面磨损深度与服役次数之间的关系,以磨损值为判据,预测模具的使用寿命。

互联网摘选

7、

The late stage of subsidence was featured by a large-scale and whole motion, indicating the isostatic compensation mechanism at depth became dominant.

晚期转变为大范围的整体沉降,显示重力均衡和补偿过程是从浅往深发展的。

互联网摘选

8、

In comparison, the influences of the lengths of metal mandrel, insulated rod and return circuit electrode on depth of investigation are relatively small, while that of the length and width of plate electrode are relatively large.

相对而言,金属芯棒、绝缘棒和回路电极的长度对探测深度的影响较小,而极板的长度和宽度影响较大。

互联网摘选

9、

The survey and analysis show that when the rut depth is deeper ( more than 60 mm), the greater deformation would be found both in wearing course and binder course, and the compression deformation ratio of binder course is higher than that of wearing course.

测量分析结果表明,车辙深度较深(大于60mm)时,上、下面层均发生了较大的变形,且下面层的压缩变形率大于上面层;

互联网摘选

10、

The diffuse speed and depth of Si element in rapid solidification brazing metal are higher than that in as-cast one.

快冷钎料中Si元素在母材中的扩散速度和深度都远高于普通铸态钎料。

互联网摘选

11、

Studying shows that the larger of the linear array is, the greater of the depth of blind angle is and the smaller its sensitivity of amplitude-phase errors and position errors is;

研究表明,天线单元数越多,盲角深度越大,盲角深度的幅相误盖敏感度和位置误差敏感度越小;

互联网摘选

12、

The Effect of Random Errors on The Depth of Blind Angle of Linear Arrays

随机误差对线阵盲角深度的影响

互联网摘选

13、

This paper was aiming at tea brown blight, one of the three most serious tea tree disease, for an in-depth study.

本文针对茶树三大病害之一的云纹叶枯病进行了深入的研究。

互联网摘选

14、

Results: All of the patients were quiet during the operations and the relaxation depth of abdominal muscle was good.

结果:两组患儿术中安静、麻醉满意、肌松良好。

互联网摘选

15、

The characters of the depth related VEP evoked by binocular disparity were identified after analysing and comparing the VEP superposition results.

通过立体视觉深度相关脑诱发电位提取及比较分析,对深度相关的特征视觉诱发电位发放进行了标定。

互联网摘选

16、

With the maximization of ship, the competition of the world container pivot harbor is fiercer, on one hand ultra and large-scale container ship can only berth port, which condition of depth of water, efficiency of load and unload and management level is qualified;

船舶的大型化使得世界集装箱枢纽港的竞争更加激烈,一方面超大型的集装箱船舶只能停泊在水深条件、装卸效率和管理水平符合要求的港口;

互联网摘选

17、

Depth development on beet pulp

甜菜粕的深层次开发

互联网摘选

18、

Calculating Method of Bending Resistance for the Partial Depth Endplates Composite Connection

部分端板连接梁柱组合节点抗弯承载力计算

互联网摘选

19、

Therefore, it is characteristic of cross-country skiing has been in-depth understanding.

因此,人们对越野滑雪项目特征的认识有了不断的深入。

互联网摘选

20、

Construction of large quay berth is required to wharf-frontage depth and cargo-handling technology strictly, and it also brings vast foreground to application of ultra-long prestressed concrete quadrate piles in downstream silt quality area of Yangtze River.

大型泊位的建设对码头前沿水深、装卸机械的能力提出严格的要求,这给长江下游淤泥质地区超长预应力混凝土方桩的应用带来了广阔前景。

互联网摘选

  • 今日热词
  • 热门搜索

简答网英语词典(dict.jiandongshicai.cn)为您提供在线翻译、英语词典、单词大全、英译汉、汉译英等英语服务!可按单词头尾、字数和词义分类查询。支持lj:关键词格式查询例句。

用户反馈
请选择反馈类型(可多选):
您的联系方式:(如需回复请填写联系方式)
反馈内容:
提交成功 小编会尽快处理
回到顶部
点击反馈