plastic的例句大全

The principle and characteristics of magnet injection molding are explained and its key technologies are analysed from magnetic particulate, plastic binder and mold, process.

并且在磁性颗粒塑料粘结剂、模具、工艺等方面分析了该工艺的关键技术。

互联网摘选

Due to the existence of surface tension, plastic film was binder together and so difficult to separate when it was compressed or heated in accumulation and bound volumes.

塑料薄膜在堆积及缠卷时，由于表面张力的存在，当受压或受热时，容易使塑料薄膜黏结在一起，不易分离，甚至无法使用。

互联网摘选

The erosion mechanism at 90 degrees includes block exfoliation, the plastic deformation of binder phase and the extrusion of the carbides, meanwhile, the brittle fracture character has also been observed with a speed of 420 meters per second.

90°冲蚀机制包括块状剥落，粘结相的塑性变形和碳化物的挤出，420m/s冲蚀的粘结相还表现出了脆性断裂的特点，块状剥落是质量磨损率升高的主因。

互联网摘选

The wear mechanism of original WC-Ni cemented carbide during the wear process is abrasive wear with the main characteristics of plastic deformation of Ni binder phase and fall-out of WC grains, and wear resistance depends on the hardness of cemented carbide.

原始WC-Ni硬质合金的磨损以Ni粘结相的塑性变形和WC晶粒脱落为主要特征的磨粒磨损，耐磨性依赖于硬质合金的硬度。

互联网摘选

Fair Use Stoppage Clearing of Automatic Punching Binding Machine with Plastic Pipe

自动打孔塑管装订机的合理使用及常见故障排除

互联网摘选

Analysis of elastic-plastic stochastic finite element method based on probabilistic yield criterion

基于概率屈服准则的弹塑性随机有限元分析

互联网摘选

In virtue of the wave solution of plastic dynamic response of plate and the dynamic fracture theory, the critical blasting charge was derived theoretically when onset of initial circumferential crack namely critical damage happened in thin plate subjected to explosions.

应用塑性动力响应波动解及动态断裂理论，从理论上推导了薄钢板在爆炸冲击载荷作用下产生初始环向裂纹即发生临界破坏时的装药量，并得出板的临界位移理论表达式。

互联网摘选

The main products are: food mixer, blender, electric fan, electric iron etc plastic accessories, fine hardware products.

本公司主要经营：生活小家电，食物搅拌器，榨汁机，电熨斗，应急灯，电风扇等塑料配件，精细五金制品。

互联网摘选

According to the research and analysis on structural parameter, blow-up ratio, parison thickness and mandrel pattern of the injection blow moulding blank, you could determine the structural parameter of the mandrel and produce qualified injection blow plastic product.

通过对塑料注吹模型坯结构参数、吹胀比、型坯壁厚以及芯棒形成的研究分析，确定了系列芯棒的结构参数，生产出了合格注吹塑料制品。

互联网摘选

Investigation on NC Machining Method of Spiral Slots in Mould Core for Blowing Thin Plastic Film

薄膜吹塑模芯螺旋槽的数控加工

互联网摘选

Plastic? Coefficient method for prestressed concrete single bowstring arch beam bridge

单拱面预应力混凝土系杆拱梁桥极限承载力分析的截面内力塑性系数法

互联网摘选

She puts a piece of plastic tubing in her mouth and starts siphoning gas from a huge metal drum

她把一根塑料管放进嘴里，开始从一个巨大的金属桶里吸气。

《柯林斯高阶英汉双解学习词典》

The cause analysis and solutions of early destroy of ABS plastic tubing internal stress

ABS塑胶管内应力早期破坏的原因分析及对策

互联网摘选

The leads from the model are most easily made of plastic tubing, which has little tendency to kink or leak and has good bending qualities.

做为从模型引出的导管以塑料管为最方便，用塑料管不会纠结和漏气而且弯曲性能好。

互联网摘选

Coatings used in plastic outer casing of household appliances and its application

家电塑料外壳用涂料与涂装

互联网摘选

Advantage and disadvantage of design for coating line of PALADIN plastic fittings

帕拉丁塑料件涂装线设计的得失

互联网摘选

Coating process flow and design idea of coating line of PALADIN plastic fittings applied in automobiles were introduced.

介绍了应用于帕拉丁汽车中的塑料配件的涂装工艺流程和涂装线的设计思路。

互联网摘选

Bill: I bought paper plates and plastic utensils.

比尔：我买了纸盘子和塑料餐具。

互联网摘选

Effect of End-closing Rate on Performance of PTMG Polyurethane Plastic Adhesive

封端率对PTMG型聚氨酯胶黏剂性能的影响

互联网摘选

Measuring method of the closed cell proportion of insulating plastic foams for liquid hydrogen tank

液氢贮箱泡沫绝热材料闭孔率测定方法的研究

互联网摘选