In one case, the major pathological changes of autopsy lung tissue were diffuse alveolar damage, hyaline membrane formed and alveolar exudative inflammation.

1、

Cases had exudative inflammation ofter operation, 1 case had pneumonia infection. 2 cases occurred severe pain in right-up abdomen.

术后腹腔积液2例，肺部感染1例，右上腹剧痛2例，均经保守治疗治愈。

互联网摘选

2、

Objective: To know the relation between certain change in knee joint cause synovium exudative inflammation and immunological function changes.

目的：为了解某些膝关节病变引起滑膜炎性渗出与机体免疫功能变化关系，我们对46例膝关节滑膜病变患者检测了血清及滑膜腔积液免疫指标含量变化。

互联网摘选

3、

Complications occurred in 4 cases, all of them was exudative inflammation, treated with antibiotic.

术后并发症4例，均为腹腔积液，经抗炎后好转。

互联网摘选

4、

SARS is pathologically characterized by interstitial exudative inflammation of lung with the formation of hyaline membrane in acute phase.

急性期重症病例肺部病变为严重的急性间质性渗出性炎，类似呼吸窘迫综合征的病理特征。

互联网摘选

5、

For the model group: acute exudative inflammation, with serous exudation of material full of alveolar septum, the part of the alveolar structural damaged, alveolar fusion, fibroblasts, lymphocytes and collagen fibers gathering in large numbers.

模型组可见急性渗出性炎，有浆液性物质渗出，充满肺泡间隔内，部分肺泡结构破坏，肺泡融合，成纤维细胞、淋巴细胞、胶原纤维大量聚集。

互联网摘选

6、

CONCLUSION CVF can induce significantly exudative pleurisy sensitive to anti inflammatory agents.

结论CVF胸膜腔内注射能引起对常用的抗炎药敏感的渗出性胸膜炎。

互联网摘选

7、

Objective: To explore the diagnosis and treatment of senile tuberculosis exudative pleurisy.

目的：探讨老年人结核性渗出性胸膜炎诊断与治疗方法。

互联网摘选

8、

Clinical analysis of tuberculosis exudative pleurisy in the elderly: A report of 46 cases

老年人结核性渗出性胸膜炎46例临床分析

互联网摘选

9、

Discussion on the image differentiation of exudative pleurisy clinical types

渗出性胸膜炎临床证型的影像学辨证探讨

互联网摘选

10、

The movement of the carbon paste in extruder

浅析炭糊在挤压机内的运动

互联网摘选

11、

Analysis of fluid field in wide sheet extruder die with both end feeding To use this layout, the pattern pieces cannot be wider than the width of the folded fabric.

两端进料式宽幅片材挤出机头流道流场分析使用这种排料方法，样板宽度不能超过折叠后的宽度。

互联网摘选

12、

Taking the development of the extruder die for a typical complex profile rubber sealing strip as an example, the designing method and basic thought for the extruder die were introduced.

本文以一典型异型密封条挤出模头的研制为例，详细介绍了组合式异型密封条挤出模头的设计方法及基本思路。

互联网摘选

13、

Development of the extruder die for through internal-diameter-determined plastics pipes

直通式内定径塑料管挤出机头的研制

互联网摘选

14、

Application of different finite element methods to analyzing flow channel in extruder die Analysis and optimization of flow manifold system in acrylonitrile unit

几种有限元分析方法在机头流道分析中的应用研究丙烯腈急冷塔喷淋系统流道分析与优化

互联网摘选

15、

The Design of Twin-Screw Extruder Die for Special-shaped Profile Extruder and Its Application

挤出异型材用双螺杆挤塑机机头模具的设计挤扩支盘成型机及其应用

互联网摘选

16、

So provide the basis for the design of the temperature controlling system of the extruder die-

列出了方程中各个热通量的计算公式，为挤出机头温度控制系统的设计提供了依据。

互联网摘选

17、

During the production of plastic film through casting method, the cooling process of molten polymer which is extruded from the extruder die determines the quality and performance of plastic film.

流涎法生产塑料薄膜的过程中，从挤出机模头挤出的熔融聚合物的冷却过程决定着塑料薄膜的质量与性能。

互联网摘选

18、

Punching plunger extruder is a novel mechanical ram extruder which was developed based on hydraulic ram extruder and forge principle.

柱塞冲压式挤出机是在液压式柱塞推压机的基础上根据锻造原理开发的一种机械式柱塞挤出机。用柱塞冲压式挤出机可以连续挤出超高分子量聚乙烯制品。

互联网摘选

19、

Fully-hydraulic Ceramic Extruder

全液压式陶瓷挤压机

互联网摘选

20、

Pilot-plant production of φ 350mm graphite electrode with hydraulic extruder of 1500 tons

用1500吨油压机生产φ350mm石墨电极

互联网摘选