In practice, it embodies as below: widespread illegal obtain evidence through extorting a confession by torture, custody measure deviating the principle of necessity, being serious in illegal custody after expiry, abuse one's power of search and detention.

1、

Ground data pre-processing for airborne scanner

机载扫描仪地面数据预处理

互联网摘选

2、

This paper presents the new series of airborne scanner and related systems which were developed in the last 5 years.

本文介绍了在七五期间研制的新型航空扫描仪系列以及配套的技术系统的情况。

互联网摘选

3、

According to the theory analysis, mathematical mode showing the lineal relationship between the response of airborne scanner and the effective reflected brightness of targets has been established under the reasonable assumption, exact physical significance for related parameters is given.

本文从理论分析出发，在合理的假设条件下确立了航空扫描仪响应值与地面有效反射亮度成线性的数学模式并给出有关参数的确切物理含义。

互联网摘选

4、

The CCT Formatter for Airborne Scanner

机载扫描仪CCT格式器

互联网摘选

5、

The processing for dimension stability of metal scanning mirror in airborne scanner

航空扫描仪中金属扫描镜的尺寸稳定化处理

互联网摘选

6、

The off-line working CCT formatter for the airborne scanner was successfully developed according to the characteristics of the airbone scanner and the requirements of the remote sensing users.

根据机载扫描仪的特点和遥感用户的要求，精心研制了在脱机状态下运行的CCT格式器。

互联网摘选

7、

The ability to fend for oneself is indispensable to any adult, but real maturity is more than just a set of survival strategies.

独立生活的能力对于任何一个成年人来说都是必不可少的，但真正的成熟远远不只是一整套的生存策略。

互联网摘选

8、

How to Improve the Slitting Performance of Dish Knife in Finishing Lines

如何提高碟刀在铝加工精整设备中的应用

互联网摘选

9、

They have been going over hundreds of finishing lines throughout US for the past 27 years.

在过去27年里，他们在美国各地穿过了数百条终点线。

互联网摘选

10、

Force analysis and parameter calculation of guide roller, compression roller and scraper in rolling and finishing lines

轧制和精整线中引料辊、压辊和刮刀的受力分析及其参数计算

互联网摘选

11、

Several methods about lowering investment in finishing lines at starting layout design, proved to be feasible, are given.

介绍了从方案设计着手降低涂装生产线设备投资的几种方法，这些方法已被实践证明是切实可行的。

互联网摘选

12、

In some rolling and finishing lines, the expected design requirements can not obtained due to unreasonable choice of the equipments and mistaken calculation.

在轧制和精整生产线设计时，往往由于设备选择的不合理、计算上的错误，使生产线达不到预想的要求。

互联网摘选

13、

In recent years sees a lot of research and development on bamboo based panel board, and there are many new products and manufacturing equipment.

近年来，国内对竹质人造板的生产和应用进行了大量的研究和开发，涌现出了不少新产品和日趋完善的生产工艺和设备。

互联网摘选

14、

Research on the Surface Quality of Cut Bamboo Based Panel Board

竹集成材切削表面质量研究

互联网摘选

15、

Study on Developing the Domestic Cutter Used in Producing Floor Panel Board

镶拼木地板生产刀具国产化的研究

互联网摘选

16、

With dark wood panel board rooms, expensive office real estate, golden ties everywhere, conversations. That's not Frank by the way.

在硬木板的房间里，昂贵的房地产办公室，到处镀金，这不是弗兰克。

互联网摘选

17、

It is observed that worn surface data show good agreement with Kalker theory for average stress levels which less than 100 Ksi ( 7031 kg/ cm~ 2) and departing from theory increases with increase of contact stress above this value.

磨耗表面条件下进行的试验数据显示，在平均应力水平低于7031公斤/厘米~2时，上述关系与Kalker的理论相符合，当接触应力超出上述水平，则结果有所不同。

互联网摘选

18、

The Behaviour of Austenite Grain Growth and the Effect of Stress on it in 18% Ni ( 350 KSi) Maraging Steel

18%Ni（350KSi）马氏体时效钢晶粒长大行为及应力对它的影响

互联网摘选

19、

Therefore, knowledge sharing and integration ( KSI) are the most important elements of knowledge management. However, they are also difficult aspects in knowledge management.

然而，知识共享与知识整合仍然是目前知识管理的重点和难点。

互联网摘选

20、

The factors which influence polymeric kinetics of acrylate emulsion modified by vinyl alkoxy silane through seed emulsion polymerization were investigated, and the nucleation mechanism of emulsion polymerization was analyzed.

用种子乳液聚合法研究了硅氧烷改性丙烯酸酯的乳液聚合，对影响种子乳液聚合动力学的因素进行讨论，并分析了乳液聚合的成核机理。

互联网摘选