Since 1958, an engine with a single overhead camshaft has been used.

1、

Remove the camshaft retaining bolt and remove the sprockets and chain as an assembly.

拆去凸轮轴固定螺栓,并拆去作为一个总成的链轮和链条.

网络文摘精选

2、

This means that the crankshaft will make two revolutions for every revolution of the camshaft.

这意味着凸轮轴每旋转一次曲轴将旋转两次.

网络文摘精选

3、

Argon arc remelting hardening is a new technology of manufacturing camshaft.

氩弧重熔硬化是生产凸轮轴新工艺.

网络文摘精选

4、

Upward camshaft; chain transmission; timing gas distribution system is stable and has little noise.

顶置凸轮, 链条传动, 正时配气系统传动平稳,噪音小.

网络文摘精选

5、

In this paper, the theory of cam profiling by CNC swing type camshaft grinder is analyzed.

详细分析了摇架式凸轮轴磨床凸轮轮廓的数控成形原理.

网络文摘精选

6、

A camshaft driven by a chain or belt turns in the same direction as the crankshaft.

凸轮轴被链或者带驱动,使其朝着曲轴相同的方向转动.

网络文摘精选

7、

The camshaft has a cam, on which there is a lob , or bump.

凸轮轴上有一个凸轮, 凸轮上有一个凸角.

网络文摘精选

8、

The ratio of the crankshaft to the revolutions of the camshaft is 2∶1.

曲轴的转速与凸轮轴的转速之比是2∶1.

网络文摘精选

9、

The camshaft and crankshaft gears can be connected directly, or meshed.

凸轮轴和曲轴齿轮可能被直接连结, 或者相啮合.

网络文摘精选

10、

Two TDC ( Top Dead Center ) sensors are mounted at the rear of the single camshaft.

两个上死点的传感器安装在凸轮轴的后面.

网络文摘精选

11、

A formula of the camshaft rotating velocity is deduced while keeping constant metal removal rate.

推导出了保持磨除率基本恒定时,数控凸轮轴磨床磨削凸轮时凸轮轴转速变化的计算公式.

网络文摘精选

12、

The manganate phosphating technology of camshaft is introduced.

介绍凸轮轴的磷化工艺.

网络文摘精选

13、

The isothermal quenching process of the ductile iron camshaft was analyzed.

对球铁凸轮轴的等温淬火工艺进行了分析.

网络文摘精选

14、

The front timing cover and and a finished camshaft with timing gear on the end.

前面的时间和范围,并完成与凸轮轴齿轮的时间就结束.

网络文摘精选

15、

The influence of inoculant addition amount on the structure and properties of camshaft was investigated.

试验了孕育剂量对凸轮轴组织和性能的影响.

网络文摘精选

16、

As camshaft rotates, the lobe, or high spot of the cam, pushes of the valve.

当凸轮轴旋转时, 凸轮凸起的或者高点的位置, 推动气门座.

网络文摘精选

17、

The metal shaft, called the camshaft, typically has individual cams for each valve in the engine.

那金属轴叫凸轮轴, 在发动机里的每个气门一般有各自的凸轮.

网络文摘精选

18、

This is called an overhead camshaft arrangement.

这被叫为顶置凸轮轴装置.

网络文摘精选

19、

Some high-performance engines have two separate camshafts, one for each set of inlet and exhaust valves.

一些高性能发动机有两个单独的凸轮轴, 分别负责开关进气门和排气门.

互联网摘选

20、

Further engine modifications also include precision-machining the cylinder heads and fitting them with four special camshafts.

进一步的修改还包括发动机精密加工的气缸盖和装修有四个特别凸轮轴他们.

互联网摘选