Based on the number of asperities on the fault plane, the asperity model was classified into three models: all-asperity, single-asperity and multi-asperity models.

1、

Merchant thought that minute asperities existed at the chip-tool interface and the fluid was drawn into the interface by the capillary action of the interlocking network of these surface asperities.

Merchant认为：在切屑与刀具接触界面上存在微小的粗粒，切削液通过这些表面的微小粗粒组成连锁的网络的毛细管被吸入到切屑与刀具的接触界面上。

互联网摘选

2、

In this model the rough surface of the contact is idealized as a plane with some asperities. The sticking effect is also considered. The variation of contact resistance with contact force is calculated.

模型将粗糙的触头表面理想化为多微丘结构，并考虑了表面粘连效应，给出了接触电阻与接触力之间的变化关系。

互联网摘选

3、

However, at higher angle of tooth-shaped asperities and under higher normal stress, the failure model II is found, which is in first tension but final shear failure.

在较高的法向应力下，含起伏角较高齿形节理面的非贯通节理岩体可能出现破坏模式II（先张拉后剪切破坏模式）。

互联网摘选

4、

In microscope scale, a rough surface can be regarded as a series of asperities with certain stochastic distributions of asperity height, size and geometry.

从微观角度来看，粗糙表面可以近似地认为是由一系列高度、大小以及几何形状服从一定分布规律的微型粗糙峰所组成，因此粗糙峰之间的接触问题也就成为研究粗糙表面接触问题的关键。

互联网摘选

5、

Numerical results reveal that the existence of single asperities can lead pressure to change drastically and film thickness to become thin in the vicinity of the asperities.

结果表明，单粗糙峰造成接触区对应位置油膜压力剧烈变化而膜厚变薄。

互联网摘选

6、

In this paper, a three-dimensional measuring system for surface asperities is described, in which a microcomputer is interfaced to a stylus profilometer.

本文介绍采用触针式轮廓仪与通用微型机相连的表面三维形貌测量系统。

互联网摘选

7、

The highest temperature of asperities is much higher than that of worn plane, which is one of the main factors in leading to stress graphitization on worn surface.

摩擦过程中粗糙表面微凸体的最高温度远大于摩擦平面，瞬时的高温和摩擦剪切力的作用使微凸体被应力石墨化。

互联网摘选

8、

The relationship between sliding friction force and contacting condition of rough surfaces was developed according to kinematics and dynamics analysis of two contacting asperities.

从一对微凸体的接触力学和运动学分析出发，建立了非流体动力润滑条件下粗糙表面滑动摩擦阻力与粗糙表面接触状态间的关系。

互联网摘选

9、

Based on the interaction of asperities and upper-bound approach a mathematical model for simulation of friction phenomenon between dies and workpiece was proposed.

本文中以刚性微凸体与可变形微凸体的相互作用模拟金属压力加工过程中模具与工件之间的摩擦过程，并用上限法分析所提出的模型。

互联网摘选

10、

The influence of density distribution and height of the asperities on nonlocal friction is also studied here. A experimental system for friction test is designed.

分析了微凸体分布密度不同、微凸体高度不同时，非局部摩擦的影响变化规律。

互联网摘选

11、

She was oppressed by an abiding sense for the asperities and inequalities of society.

她深受压抑，长期因社会的冷酷和不公深受困扰。

互联网摘选

12、

The larger the surface roughness and the sharper the asperities, the greater the asperity contact load.

表面越粗糙、表面凸峰越尖锐，微峰接触载荷则越大。

互联网摘选

13、

Earthquake doublet in Kagoshima, Japan: rupture of asperities in a stress shadow

日本鹿儿岛的地震对：应力影区中的凹凸体破裂

互联网摘选

14、

Far-field body-wave radiation of the fault which contains asperities

含粗糙面断层的远场体波辐射

互联网摘选

15、

Study on the characteristics of rock failure strain and acoustic emission field for two parallelling faults with the same slip direction including asperities

含障碍体滑动方向相同平行断层失稳破坏应变场、声发射分布特征的研究

互联网摘选

16、

Propagation of an aseismic dislocation through asperities with smooth borders

穿过具有平滑边界凹凸体的无震位错的传播

互联网摘选

17、

Whatever it was had thrown her Dodge off course as she rounded a sharp curve.

就在她急转弯时,不知是什么东西使她的道驱车脱离了车道.

互联网摘选

18、

It is a sharp curve in the road.

这是急转弯.

词典精选例句

19、

Strip steel but deep treatment is canal of cold belt, solder, cold curved bar to wait.

带钢可深加工为冷带、焊管、冷弯型钢等.

互联网摘选

20、

A smile is just a genly curved line that sets a lot of things straight.

微笑仅是一道弯弯的弧线,却可以使很多事变直.

互联网摘选