The last chapter puts forward suggestions and countermeasures to improve the profitability of credit card business from the angle of the issuing bank and government.

The simulation algorithms of wave high, yaw force, rolling moment and sway moment were put forward. Meanwhile, it also discusses the influence of roll yaw on sideslip in spin, and of moving round plumb line on angle of bank.

给出了随机海浪波高、横荡力、横摇力矩、艏摇力矩的仿真算法。同时就尾旋中偏滚对尾旋侧滑的影响、绕铅垂轴旋转对坡度的影响等进行了讨论分析。

互联网摘选

The seepage and erosion are primary dynamic influence factors on bank failure; and the soil composition, soil distribution and slope angle of bank are primary internal influence factors on bank failure.

指出了坡内的渗流作用与坡前水流的冲刷作用是岸坡发生崩塌的主要动力因素，而岸坡土体的物质组成和分布、岸坡坡度等则是岸坡发生崩塌的主要内在因素；

互联网摘选

Meanwhile, it also discusses the influence of roll yaw on sideslip in spin, and of moving round plumb line on angle of bank.

同时就尾旋中偏滚对尾旋侧滑的影响、绕铅垂轴旋转对坡度的影响等进行了讨论分析。

互联网摘选

Institutional barriers faced to Country Bank when it has been build are analyzed from three angle of bank access, bank operations and bank retirement.

本章从银行准入、银行运营和银行退出三个角度分析了县域银行创设后面临的制度障碍。

互联网摘选

At the angle of bank management, it can be seen coming from the external factor and inside factor.

从银行管理的角度出发，更可将其认为来自银行外部因素和银行内部因素。

互联网摘选

The Relationship between The National Government and Shanghai Bank Industry from the Angle of Bank Laws in The 1930s

从银行立法看30年代国民政府与沪银行业关系

互联网摘选

Analysis of the computation method for measuring the angle of bank deflection at fixed point

定点测量倾斜偏角计算方法分析

互联网摘选

Analysis and experiment on the taper angle of contact surface of bend rotation ultrasonic micromotors

弯曲旋转超声电机接触界面锥形角的分析与实验

互联网摘选

The paper puts forward the concept of normal angle of winding bend for describing the degree of distortion and deformation of malformed winding bend.

为了描述畸形河湾扭曲变形的程度，提出了河湾法向角的概念。

互联网摘选

We still make characters on the wall directly and deform the big characters through the angle of bend making by wall.

此项目我们依旧采用直接在墙面上做字，并且将大的字体借助墙面的转折角进行变形，使之成为字体的再设计。

互联网摘选

Tube bending is a process by which a straight piece of tube is formed to a selected radius and angle of bend.

弯管工艺是指将平直的管子按选定的半径和弯曲角度弯曲成形。

互联网摘选

The experimental results show that the total pressure loss and outlet derivation angle can be retained in an acceptable range when the bend angle of van rear end is less than a specific value, reaching the aim of adjusting the outlet angle of variable curvature cascade.

研究结果表明：叶片弯角小于一定值时，叶栅的总压损失和出口气流落后角保持在可接受的范围，能达到调节气流出口方向的目的；

互联网摘选

In this paper, with the principle of high pair replaced by low pair, the cam mechanism is transformed to linkage, through the analysis of the linkage the equation of the pressure angle and the radius of curvature and profile of cam is established.

本文运用高副低代原理，将凸轮机构转化为低副机构，通过低副机构运动分析建立起凸轮廓线、曲率半径及压力角表达式。

互联网摘选

Focusing on the research of some important design parameters impacting the carrying capacity of the bearing, including radial clearance, contact angle and groove radius of curvature coefficient, a detailed analysis was given, and the corresponding bearing design recommendations were presented.

着重对影响轴承承载能力的重要设计参数径向游隙、接触角、沟曲率半径系数等进行了仿真，并给予了详细的分析，提出了对应的轴承设计建议。

互联网摘选

In this paper, the pressure angle and minimal radius of curvature of cam mechanism with swinging roller follower are discussed in details.

本文对摆动从动杆盘状凸轮机构的最大压力角和最小曲率半径问题进行了详细的讨论。

互联网摘选

Computation of S_1-stream sheet of axial air compressor with small installing angle by use of streamline curvature method

小安装角轴流压气机S1流面的流线曲率法解

互联网摘选

Nozzle flow field of SRM was numerically simulated with Fluent software. The effects of nozzle convergent half angle, radius of curvature on upstream of throat section and length of throat cylinder on flow field are investigated.

用Fluent计算流体力学软件对固体火箭发动机喷管流场进行了数值计算，研究了喷管收敛半角、喷管喉部上游圆弧曲率半径和喉部圆柱段长度对喷管流场的影响。

互联网摘选

Mathematical formulas are derived comprehensively and systematically for the profile coordinate, pressure angle and radius of curvature of the cylindrical cam with an oscillating roller follower.

推导了摆动滚子从动件圆柱凸轮廓线、压力角及廓线曲率半径方程，讨论了该种凸轮机构在各种运转情况下与之相适用的方程。

互联网摘选

The article mainly discusses optical angular deviation affected by angle of incidence, curvature, refractive index and unparalleled faces in order to modify the windscreen processing.

本文主要讨论由上述因素引起的入射角、折射率、楔形度、厚度与曲率半径的比值对光学角偏差的影响，以利于生产工艺的控制。

互联网摘选

Water Flow Behaviors of Channel Bend in Middle Sized Radius and Big Bend Angle of Curvature

中等半径大偏转角弯道的水流特性

互联网摘选