The Determination of a Cam's Allowable Pressure Angle

1、

The practical problem of the allowable pressure of the proposed bearing layer is discussed.

并探讨了有关建议中提出的桩端持力层容许承载力参考数值的实用问题。

互联网摘选

2、

The relative factors are discussed: maximum allowable pressure inside the site, permeating coefficient of of MSW, bio-gas production rate, diameter of the well, etc.

同时讨论了影响控制范围的各主要因素：垃圾层中最大允许压力、垃圾层的透气性能、垃圾的产气速率等。

互联网摘选

3、

On the basis of well side investigations, this paper analyses the reasons that sliding sleeve can't open within the range of allowable pressure and proposes corresponding measures.

通过现场实践，分析滑套在允许压力范围内打不开的原因并采取相应措施，在实践中起到了很好的效果。

互联网摘选

4、

Design allowable stress of arch dam in China comparing with that in American

中国拱坝设计容许应力与美国的比较

互联网摘选

5、

Influence of Lowered High-temperature Allowable Stress on Application of Steel CASE 2180

高温许用应力下调对CASE2180钢使用的影响

互联网摘选

6、

The analysis results show that the strength of the axle satisfy the allowable stress requirements.

分析结果表明，该车轴强度满足材料的许用应力要求。

互联网摘选

7、

Based on mechanical analysis and testing research, the paper put forward a calculation method of interlayer allowable shear stress and the design method of asphalt pavement considering shear strength.

并且，在力学分析和试验研究的基础上，提出了层间容许剪应力的计算方法和考虑抗剪强度的沥青路面结构设计方法。

互联网摘选

8、

Discussion on the Increased Range of Allowable Stress in the Design Code for Industrial Metallic Piping

对工业金属管道设计规范中许用应力提高幅度的探讨

互联网摘选

9、

Allowable stress and strength design method of masonry code in the United states& flexure design

美国砌体规范的容许应力与强度设计方法&梁的抗弯设计

互联网摘选

10、

As for the calculation, the old allowable stress design method and the more simple formula are adopted, not the present limit condition calculation method and its complicated formula stated in the 《 Steel Structure Design Code 》.

在计算方法上不是采用现行《钢结构设计规范》中的极限状态设计法及其较繁的计算公式，而是采用锅炉行业过去习惯采用的许用应力设计法及其较简单的计算公式。

互联网摘选

11、

Ultimate state analysis of carrying capacity and tensile fatigue analysis are conducted according to basic combination of loads effect and standard combination of loads effect respectively. Design of foundation screws through allowable stress design method is presented.

按荷载效应的基本组合进行承载能力极限状态分析，按荷载效应的标准组合进行抗拉疲劳分析，采用许用应力设计法进行地脚螺栓的设计。

互联网摘选

12、

Strength Design values may be converted to Allowable Stress Design values.

设计要求、强度设计值可转换为许用应力设计值。

互联网摘选

13、

On the part of estimating the financial risk of the allowanced corporation, the most important factor is that payoff period is too long ( 28.1%).

在特许公司财务风险评估方面，最重要者为回收期间过长（28.1%）。

互联网摘选

14、

In1958, art historian and critic, Lawrence Alloway, first used the term "pop" to describe the strong influence of popular culture on society, especially in the arts.

1958年，史学家兼批评家劳伦斯•阿洛威首次使用“波普”一词来形容流行文化对社会、尤其是艺术方面的巨大影响。

互联网摘选

15、

Dr Alloway commented: "I like to describe it as your brain's Post-It note."

阿洛韦博士解释说：“我喜欢把这形容成是你大脑的记事贴。”

互联网摘选

16、

Allozyme Method in Study on Population Genetics of Pinus yunnanensis

云南松居群遗传学研究的等位酶分析方法

互联网摘选

17、

Genetic relationship of some lily cultivars by allozyme data

几个百合品种遗传亲缘关系的等位酶分析

互联网摘选

18、

Specific expression of EST cat got allozyme gene in Maize

玉米EST、GOT、CAT等位酶基因的表达特异性研究

互联网摘选

19、

Allozyme Polymorphism and its Relationship to Quantitative Traits Diversity of Local Varieties

玉米地方品种同工酶的遗传多样性及其与数量性状的关系

互联网摘选

20、

The myth was started in the 1920s by a psychologist, Floyd Allport, whose evolutionary spin job was attributed to Darwin, thus launching nearly a century of misguided beliefs.

这种说法源于上世纪20年代的心理学家弗洛伊德？奥尔波特（Floyd Allport），他的进化论解释工作被认为是出自达尔文，这致使错误的观点延续了近一个世纪。

互联网摘选