Through bending experiment, adhesive materials failure point and load of toughened and not toughened samples are analyzed and the toughening modification of adhesive materials can improve the adhesive properties between CFRP and concrete.

1、

This predictive method is introduced detailedly. 2 、 The initiation and propagation of fibre damage, matrix cracking, delamination and adhesive failure of repaired composite laminates as well as coupling effect among them is investigated.

对该方法作了详细介绍。2、对楔形修补层合板的纤维断裂、基体开裂、层间分层以及胶层脱胶等损伤的萌生和扩展以及它们之间的耦合作用进行了研究。

互联网摘选

2、

Effect of curing procedure on the impact toughness of adhesively bonded joints

固化工艺对胶接接头冲击性能的影响

互联网摘选

3、

Crack tip stress field of adhesively patched pressure vessel shell

压力容器壳体胶结补强后的裂尖应力场

互联网摘选

4、

Interface toughness of adhesively jointing structures is an important parameter in adhesive structure design.

界面韧度是粘结结构设计的一个重要参数。

互联网摘选

5、

Viscoelastic stress analysis of adhesively bounding joint on axisymmetric composite shell

轴对称壳体胶连接头粘弹性应力分析

互联网摘选

6、

Influence of Sizes Patch on Adhesively Bonded Composite Structure Strength

补片尺寸对复合材料胶接修理性能的影响

互联网摘选

7、

Effect of magnetic field on shear strength of adhesively bonded single lap joint

外加磁场对粘接接头剪切强度的影响

互联网摘选

8、

Numerical Analysis of Stress Distribution of Adhesively Bonded Metal Joint under Cleavage Loading

劈裂载荷作用下金属胶接接头中应力分布的数值分析

互联网摘选

9、

Experimental study on vacuum performance of adhesively bonded joint under cyclic load

循环载荷下粘接接头真空性能的实验研究

互联网摘选

10、

Finite element analysis on reliability design of adhesively bonded single lap joint

基于有限元方法的单搭接接头可靠性设计

互联网摘选

11、

We adhibit rare earth metal in catalyst and prepare catalyst. It reduces the active component stripping and improves the stability of catalyst.

针对过渡金属氧化物活性组分易溶出的问题，向催化剂中引入了稀土金属元素，制备了催化剂，将活性组份溶出量降低为原来的16%，提高了催化剂的稳定性。

互联网摘选

12、

Reclamation of adhibit method of paraffin section

石蜡切片贴片法的改良

互联网摘选

13、

Adhibit efficiency function, The genetic annealing evolutionary algorithms are applied to realize the optimization of scheduling decisions.

引入效率函数，运用遗传退火进化算法实现了调度决策的优化；

互联网摘选

14、

Discussion About Design Method for Reducing to Adhibit Ash onto the Coal Gas Fan

煤气加压鼓风机叶轮减少粘灰设计方法的探讨

互联网摘选

15、

The global MWL lies between the two MWLs simulated under wet adiabatic and isobaric cooling processes, respectively.

全球大气水线位于湿绝热冷却过程和等压冷却过程条件下分别模拟的两条大气水线之间。

互联网摘选

16、

This paper reports the current studies on the film cooling characteristics of single-row holes on flat plate at different blowing ratios, and analyzes the distributions of adiabatic film cooling effectiveness and heat transfer coefficient downstream the film holes.

对不同吹风比条件下的典型单排孔冷却结构的平板气膜冷却特性进行了实验研究，对冷却孔下游的气膜冷却效率及换热系数分布规律进行了分析。

互联网摘选

17、

Numerical study on adiabatic wall cooling effectiveness and convective heat transfer coefficient of effusion cooling

致密孔阵气膜冷却绝热温比和对流换热系数的数值研究

互联网摘选

18、

Adiabatic ablation cooling, film cooling are the main means and have been used widely.

隔热层烧蚀冷却、气膜冷却是冲压发动机常用的冷却方式。

互联网摘选

19、

Adiabatic film cooling effectiveness downstream of primary jet in combustion chamber

燃烧室主燃孔下游气膜绝热温比研究

互联网摘选

20、

The rate of change of δ 18O against temperature in the process of wet adiabatic cooling is smaller than in the process of isobaric cooling under the same humidity.

在相同的湿度条件下，湿绝热冷却过程中δ18O随温度的变化率小于等压冷却过程。

互联网摘选