Analysis of Friction Losses for Double Crank and Connecting Rod Diesel Engine

1、

Modeling and optimization of double crank slide block steering mechanism

双曲柄滑块式转向机构的建模及优化研究

互联网摘选

2、

Motion Analysis of the Planetary Gear Drive of the Double Crank Type

双曲柄式行星齿轮传动的运动分析

互联网摘选

3、

Application of model 160 double crank camera in strategic range

双曲柄式160摄影机在战略靶场中的应用

互联网摘选

4、

Optimized of parameters of basic dimensions of double crank shaft mechanism

双曲柄机构基本尺寸参数的优化

互联网摘选

5、

A New Design Method of Double Crank Mechanism

双曲柄机构设计新方法

互联网摘选

6、

Crank angle between extreme position effects transmission performances of mechanism in crank-slider mechanism directly.

在曲柄滑块机构中，极位夹角θ的大小直接影响到机构的传动性能。

互联网摘选

7、

Range of Crank Angle Between Extreme Positions for Planar Four-bar Linkage

平面四杆机构极位夹角的取值范围

互联网摘选

8、

Research on Transmission Performances of the Crank Angle Between Extreme Position in Crank-slider Mechanism

极位夹角对曲柄滑块机构传动性能影响的研究

互联网摘选

9、

More Analysing and Studying the Definition of Crank Angle between Extreme Positions

对极位夹角定义的进一步分析和研究

互联网摘选

10、

Development of Crank Angle 'Window' Controller for IC Engine

内燃机曲轴转角窗口控制器的研制

互联网摘选

11、

Each quantity is considered to be a function of the crank angle and radial position in the combustion chamber.

各计算量均作为曲轴转角和燃烧室径向位置的函数；

互联网摘选

12、

The transient change of discharge coefficient via engine crank angle is calculated for the first time.

首次计算出连接通道流量系数随曲轴转角的瞬时变化规律。

互联网摘选

13、

With the third steps and the fourth steps natural frequency vibration, the smaller close to the second crank arm of crankshaft and round place natural frequency of the main shaft transition the position is.

以第3阶和第4阶固有频率振动，位置越靠近曲轴第二个曲柄臂与主轴过渡圆处固有频率越小。

互联网摘选

14、

Turn the wiper module over and remove the nut that secures the wiper motor crank arm to the wiper motor output shaft.

转动雨刷模组盖，并拆下将雨刷马达曲柄臂固定于雨刷马达输出轴上的螺帽。

互联网摘选

15、

The RW Series Rotary Actuator design utilizes two independent piston cylinders, each piston has a crank arm attached to a crankshaft.

在RW系列旋转式驱动器设计采用两个独立的活塞筒，每个活塞有曲柄连接曲轴臂。

互联网摘选

16、

The machining of deep bolt holes in the air compressor's crank arm Machining of Threaded Holes in Engine Con Rods

空压机连杆两螺栓孔的深加工6102柴油机连杆螺栓孔的加工

互联网摘选

17、

The crankshaft machining complex lathe turned the crank arm journal with the way of servo turning methods.

曲轴加工复合车床通过随动车削的方式对曲轴连杆轴颈进行加工。

互联网摘选

18、

Operations on multi-points are available through the crank arm framework.

多点式操作可通过曲柄臂框架。其结构简单轻便，运作畅顺。

互联网摘选

19、

Affix using one of the crank arm fixing bolts.

词缀使用其中的一个曲柄臂固定螺栓。

互联网摘选

20、

Then, it introduces CAD model into the finite element software, and accurately calculates bell crank rigidity and fillet stress concentration factor, which is used to analyze subsequent torsional vibration and strength.

将CAD模型导入有限元软件，计算求取准确的曲拐刚度及圆角应力集中系数，用于后续扭振及强度分析。

互联网摘选