缺陷的例句大全

Growth and Defects Observation of YVO_4 Birefringent Crystal

钒酸钇双折射晶体生长及缺陷观察

互联网摘选

Garcia-Tolson, who was born with multiple birth defects, had both legs amputated when he was 6 years old.

Garcia-Tolson出生时就有很多先天缺陷，6岁时，双腿被截止。

互联网摘选

How to prevent concrete surface blemish of the highway tunnel line brick

浅谈如何防止公路隧道衬砌混凝土表面缺陷

互联网摘选

The Safe Reliability of Surface Blemish for the Liquid Chlorine Steel Cylinder

液氯钢瓶表面缺陷的安全性分析

互联网摘选

Currently the examination work of the copper flat line surface blemish depends on a person with a naked eye.

目前，连续挤压设备生产的铜扁线表面缺陷的检测工作是依靠人的肉眼检查。

互联网摘选

Within the blind angle area of the Amalog Sonoscope leakage flux inspection system, the rotary rolling caused flaws in seamless steel pipes were missed quite often due to low detection sensitivity.

无缝钢管表面的斜轧缺陷，因位于漏磁纵横向检测机组的盲角区域，检测灵敏度低，容易漏检。

互联网摘选

This paper particularly introduces how to reduce two main welding defeat made in resistance spot welding for VDSS: blistering and gas expulsion holes.

前言：本文重点介绍了如何减少V DSS钢板点焊时容易产生的两种主要焊接缺陷：鼓包和气孔；

互联网摘选

Those afflicted with SCA also lose the defective blood cells up to 12 times faster than those without the disorder. A mutation in one of the genes responsible for hemoglobin is the root cause of the disorder and it seems to be most prevalent among those whose ancestors lived in areas where malaria was common.

饱受SCA折磨的病人会以常人12倍的速度丢失缺陷血细胞。血红素基因的一处变异是这种疾病的根本原因，而且它似乎在其先人所住的疟疾肆意地区更为盛行。

互联网摘选

Casting Technique of the Aluminum Alloy Right Box and Prevention of Slag Blowhole Defects

铝合金右箱体铸造工艺及渣气孔缺陷防止

互联网摘选

The author conducts a complete and detailed theoretical analysis on the causes of raised grain defect during the fabrication of lattice mesh plate in the numerical control small punch spinning drying equipment in the article.

文章就数控小孔冲床加工纺织烘干设备中帘子网眼平板产生波浪纹缺陷的原因，进行了全面、详细的理论分析。

互联网摘选

In NDT ( Non-destructive Testing ) of weld flaw, UT ( Ultrasonic Testing ) is an important method.

在焊接缺陷的 无损 检测中, 超声检测是一种重要的无损检测方法.

互联网摘选

The dehydration of Si-OH group under high temperature led to the transformation of abridging oxygen of OH to bridging oxygen, which caused the disappearance of structure defects and formed the long-range order structure of cristobalite.

高温下Si OH基团的脱水反应使硅藻土结构中以OH-形式存在的非桥氧变成桥氧，原来的结构缺陷消失，有利于降低方英石的形成温度；

互联网摘选

An automatic surface quality inspection system installed on a finishing line of cold rolled strips is introduced. Surface defects on cold rolled strips, such as scratches, coil breaks, rusts, roll imprints, and so on are detected.

介绍一套在精整线上使用的冷轧带钢表面质量自动检测系统，该系统用于在线检测划痕、折印、锈斑、辊印等常见的冷轧带钢表面缺陷。

互联网摘选

MECHANISM OF CROSS BREAKS DEFECT FORMATION AND COUNTERMEASURES Thus, resulting harmfulness from the cross breaks may be diminished or eliminated by controlling profile and optimization of uncoilling operation.

横折缺陷的产生机理与治理对策在此基础上，提出了生产中控制板形和优化开卷操作以消除和减轻横折危害的措施。

互联网

Cause Analysis of Cross Breaks of Chromium-Free Fingerprint Resistant Sheet and Corresponding Countermeasures

无铬耐指纹板表面皱纹缺陷产生原因分析及对策

互联网摘选

Cross breaks are formed on the surface of cold rolled and tempered strip during temper rolling, which influence the surface quality and mechanical characteristics of the temper rolled strip.

冷轧退火后的带钢在平整过程中产生横折印缺陷，严重影响平整后带钢的表面质量及其力学性能。

互联网

It is necessary to establish rational elongation and tension, control the quality of coming strip strictly, to avoid cross breaks, improve the surface quality of strip.

制定合理的伸长率和张力制度，严格来料质量要求，可以避免横折印缺陷的产生，提高平整带钢的表面质量。

互联网

Strip breakage and roll wind-up frequently occur on the ZR 20 when rolling the fragile stock with severe quality problems such as worse shape, serious surface and edge defects.

森吉米尔轧机（ZR20）在轧制板形不好、板面和边部有严重缺陷的脆性原料时，经常出现的生产故障是断带缠辊。

互联网摘选

An corrective method to correct of the inherent flaw of the asynchronization direct counting circuit

直接计数式T/D电路固有缺陷的改善算法

互联网摘选

Due to the special structure and strict technical requirements of the front shock absorber sleeve of motorcycle, which leads to casting defects, such as shrinkage porosity, surface blowhole, are very easy to occur in production.

铝合金摩托车液压式前减震器筒体特殊的结构、严格的技术要求，导致生产中铸件很容易出现缩松、皮下气孔等缺陷。

互联网摘选