模拟的例句大全

Additionally, DTA shows the improvement in thermal stability in WTe: Er glass. Finally, the gain characteristics of NbP: EY and WTe: Er fiber amplifiers are simulated.

此外，差热分析表明WTe：Er玻璃的热稳定性也有所提高。3.数值模拟了NbP：EY玻璃和WTe：Er玻璃光纤放大器的增益特性。

互联网摘选

In order to test X-ray laser ( XRL) series programs, simulations of some experiments of Ne-like Ge XRL were completed, including domestic experiments driven with long-pulse ( 1ns) and international experiments driven with multiple-pulse.

介绍了用国内1ns长脉冲和国外多脉冲驱动的类氖锗的实验数据检验X光激光的理论模拟程序系列的工作。

互联网摘选

Theoretical simulation shows that, using 1% pre-pulse, if appropriate optimization of time interval between pre-and main pulse has been conducted, the output energy of XRL as well as conversion efficiency of energy can be dramatically enhanced.

理论模拟还表明，采用1%左右的预脉冲强度并对预主脉冲时间间隔进行优化，X光激光的输出能量和能量转换效率将获得大幅度提高。

互联网摘选

The bipolar packed bed cell ( BPBC) was used in the treatment of simulated nitrobenzene wastewater. The effects of voltage, mass concentration of Na_2SO_4, pH and initial mass concentration of nitrobenzene on the electrolysis were studied.

用复极固定床电解槽处理模拟硝基苯废水，考察了电解电压、Na2SO4质量浓度、pH、硝基苯的初始质量浓度等条件对电解效果的影响。

互联网摘选

The application results shows that the health monitor system for TPS units are proper and reliable, which satisfies the requirements of TPS testing.

应用结果表明，该系统满足跨声速风洞涡轮动力模拟器试验设备对安全监控系统的技术要求。

互联网摘选

These include the simulation of full-scale ship wake distribution in water tunnel and pressure measurement in the case of cavitating propeller on the dummy model by using pressure transducers as well as the expression of the experiment results and analysis method.

这包括在水筒内模拟实船伴流，测定在空泡情况下的脉动压力，试验结果的表达及分析方法。

互联网摘选

LMS method was suggested to estimate FETF for single pulse measurement. The computer simulation results have shown that LMS method is much better than empirical FFT method.

对于单脉冲激励的测量方法，我们建议采用LMS估计方法，计算机模拟结果表明LMS方法优于经典的FFT方法。

互联网摘选

The method of friction-contact coupled nodals ( FCCN) is used to simulate the contact problem and it has the advantages of being clear in concept and convenient.

应用摩察-接触耦合结点（FCCN）模拟不同介质间的接触问题，结果表明：该方法具有概念清晰和使用方便等优点。

互联网摘选

This artical introduces the measuring process and the results by this technology.

介绍了用热模拟实验机测定冷轧变形抗力的测试过程和测试结果.

互联网摘选

Dongyang Zhang ( Engineering Thermophysics) Directed by Hongde JiangA fast and accurate numerical method for non-equilibrium wet steam flow ( FAWS) is developed in this thesis.

本文主要工作是非平衡态湿蒸汽流动快速准确数值模拟方法（FAWS）的研究。

互联网摘选

The existing nonlinear methods include gradient method, newton algorithm, global search method, Bayesian algorithm, Monte Carlo method, simulated annealing algorithm and genetic algorithm.

现行的非线性方法主要有：梯度法、牛顿法、全局搜索法、Bayesian法、蒙特卡罗法、模拟退火法与遗传算法等。

互联网摘选

CBRM algorithm also introduces a "lock" mechanism, to avoid deadlock and infinite iteration of the phenomenon of distributed algorithms. Finally, we use OMNET++ simulation tool CBRM algorithm simulation.

CBRM算法还引入加锁机制以避免分布式算法的无限迭代及死锁现象。最后采用OMNET++仿真工具对CBRM算法进行了模拟实验。

互联网摘选

At first, the CBCT projection data was simulated with computer simulation technology.

首先，运用计算机仿真技术模拟出锥束CT投影数据；

互联网摘选

Analysis and simulation of optical cavity in CAEP far-infrared FEL

远红外自由电子激光光腔改进的模拟分析

互联网摘选

The paper mainly studies the stimulating training system when gun direct firing.

本课题主要研究火炮直瞄射击训练模拟系统.

互联网摘选

Nowadays most trigger circuit of plasma torch power supply of our country are simulation device controlling.

目前等离子体炬电源的移相触发电路大都是模拟式触发电路,器件参数较为分散.

互联网摘选

In this paper numerical simulation of turbulence is reviewed and commented briefly.

讨论了紊流数值模拟的发展历史、现状及趋势.

互联网摘选

Ant Colony Optimization is a novel optimization algorithm of simulated evolutionary algorithms.

蚁群优化算法是一种新型模拟进化的优化算法.

互联网摘选

Numerical analysis can only simulate the former two phases of creep deformation.

而且,数值分析只能模拟蠕变变形的前两个阶段,迄今为止,人们对蠕变第三阶段的分析较少.

互联网摘选

The V-anvil drawing process of large forgings was simulated using FE software, and the stress-strain distributions in the plastically deforming area were compared after different V-anvils drawings.

利用有限元软件模拟了V型砧的锻造拔长过程，并对不同夹角的V型砧压下后锻坯塑性变形区内应力、应变的状态进行比较。

互联网摘选