- 重点词汇
- CNCabbr.Computerized Numerical Control 电脑数值控制;新集装箱运输;
- andconj. 和，与;而且;于是，然后;因此;
- isvt.& vi. 是(be的三单形式);
- measurementn.量度;份量，尺寸;测量法;（量得的）尺寸;
- centern.篮球中锋，中场手;中心;中心区;中央;中枢;核心;焦点;（议会等的）中间派，中心站（或场，所），中线
- evaluationn.估价;<数>赋值;估计价值;[医学]诊断;
- ofprep. 关于;属于…的;由…制成;
- errorn.错误;差错;谬误;
- inprep. 在里面;在(某范围或空间内的)某一点;在(某物的形体或范围)中;在…内;在…中;进入
- thispron.这，这个;这事，这人;这时;下面所说的事;
- measuringv.量( measure的现在分词 );测量;衡量;量出;
- CAMS[医][=computer-assisted monitoring system]计算机辅助监护系统;
- 相关例句
Cylinder graduation-groove-cam is a kind of daily cam in the pattern of many kinds of cams.
圆柱分度槽凸轮是多种凸轮型式中的一种常用凸轮.
互联网摘选
本文研究直接在三坐标测量机上检测凸轮并评定误差的方法和理论.
互联网摘选
Angular velocity grinding and linear velocity grinding are the main grinding method for camshaft.
工件恒角速度磨削和工件恒线速度磨削是目前精加工凸轮轴的主要磨削加工工艺.
网络文摘精选
These engines are known as dual overhead camshaft ( DOHC ) engines.
这些发动机被称为双顶置凸轮轴 ( DOHC ) 发动机.
网络文摘精选
Since 1958, an engine with a single overhead camshaft has been used.
从1958年起, 便已使用带有单顶置凸轮机的发动机.
词典精选例句
Remove the camshaft retaining bolt and remove the sprockets and chain as an assembly.
拆去凸轮轴固定螺栓,并拆去作为一个总成的链轮和链条.
网络文摘精选
This means that the crankshaft will make two revolutions for every revolution of the camshaft.
这意味着凸轮轴每旋转一次曲轴将旋转两次.
网络文摘精选
Argon arc remelting hardening is a new technology of manufacturing camshaft.
氩弧重熔硬化是生产凸轮轴新工艺.
网络文摘精选
Upward camshaft; chain transmission; timing gas distribution system is stable and has little noise.
顶置凸轮, 链条传动, 正时配气系统传动平稳,噪音小.
网络文摘精选
In this paper, the theory of cam profiling by CNC swing type camshaft grinder is analyzed.
详细分析了摇架式凸轮轴磨床凸轮轮廓的数控成形原理.
网络文摘精选
A camshaft driven by a chain or belt turns in the same direction as the crankshaft.
凸轮轴被链或者带驱动,使其朝着曲轴相同的方向转动.
网络文摘精选
The camshaft and crankshaft gears can be connected directly, or meshed.
凸轮轴和曲轴齿轮可能被直接连结, 或者相啮合.
网络文摘精选
Two TDC ( Top Dead Center ) sensors are mounted at the rear of the single camshaft.
两个上死点的传感器安装在凸轮轴的后面.
网络文摘精选
A formula of the camshaft rotating velocity is deduced while keeping constant metal removal rate.
推导出了保持磨除率基本恒定时,数控凸轮轴磨床磨削凸轮时凸轮轴转速变化的计算公式.
网络文摘精选
