coolant的例句大全

Research on Two-phase Countercurrent Flow in Reactor Hot Leg at the Loss of Coolant Accident

反应堆失水事故条件下热管段内的两相流逆向流动研究

互联网摘选

The coolant temperature, intake port deposit, cranking speed and ignition timing all influence the limit with various mechanisms.

拖动转速、冷却水温度、进气道油膜残留和点火时刻等燃烧边界条件都对窗口区域造成影响。

互联网摘选

Some important parameters ( coolant void reactivity, burn-up and etc.) are calculated using the code WIMS-AECL.

用WIMS-AECL程序计算了参考栅元的冷却剂空泡反应性、燃耗等参数。

互联网摘选

Experimental investigation on 1% small break loss of coolant accident of pressurized water reactor cold leg

PWR冷管段1%小破口失水事故实验研究

互联网摘选

The simultaneous injection into cold leg and hot leg for more reactor core safety during large break loss of coolant accident

大破口失水事故时冷热段同时安注反应堆堆芯会更安全

互联网摘选

A Small Break Loss of Coolant Accident ( SBLOCA) experiment NSB 6 was carried out at the High Pressure Integral Test Facility ( HPITF). The break was oriented at the bottom of the horizontal cold leg with its area of 2%.

在高压综合实验装置（HPITF）上进行了压水堆冷管段2%小破口失水事故实验（NSB－6），破口方向为冷管段底部，破口面积为2%。

互联网摘选

Rust is the reason why changing engine coolant according to schedule is a good idea.

定期更换发动机冷却液是防止生锈的良方.

互联网摘选

The thermal decomposition of oxidizer/ addictive system and coolant JW/ addictive system has been analyzed by DSC and DSC-TG techniques.

通过DSC及DSC-TG联用技术分析了氧化剂AP和添加剂体系及降温剂JW和添加剂体系的热分解。

互联网摘选

Direction of connection for RSB and RSF coolant is different.

RSB与rsf之冷却剂连接方向不同.

互联网摘选

Add some coolant into the radiator , please.

请给水箱里加些冷却液.

互联网摘选

The primary heat exchanger ( PHX) is a key heat transmission equipment of the lead alloy cooled reactor, and it is also a safety barrier to prevent the radioactive lead alloy coolant.

主换热器是铅合金冷却反应堆中关键的热传输设备，同时也是防止一回路放射性冷却剂外逸的一道安全屏障，此外，换热器结构设计合理性也将直接影响反应堆安全性及经济性。

互联网摘选

Use only coolant additives approved for this engine by porsche.

仅可对此发动机使用保时捷认可的冷却液添加剂。

provided by jukuu

The influence of the coolant on cutting performance of saw blade are outlined.

概述了冷却液对锯片切割性能的影响.

互联网摘选

Plastic injection mould , coolant passages, eject pin and electrical heating holes.

塑胶射出模具?冷却水孔 、 射梢孔及电热孔.

互联网摘选

Plastic injection mould-coolant passages, eject pin and electrical heating holes.

塑胶射出模具 - 冷却水孔 、 射梢孔及电热孔.

互联网摘选